What Happens During a Professional Tree Felling Job?

Your Local Arborist and Tree Surgeon

  • Home
  • /
  • What Happens During a Professional Tree Felling Job?

A professional tree felling job begins with an assessment rather than a chainsaw. The arborist checks the tree, surrounding property, access, legal restrictions and potential hazards before selecting a controlled method of bringing the tree down. The work may involve felling the whole tree into a clear area or dismantling it in sections with ropes and specialist equipment.

Every site is different. Tree size and condition matter but so do nearby buildings, roads, overhead lines, underground services and the space available for falling material. A professional process is designed around these conditions rather than applying the same technique to every tree.

What does a professional tree felling job involve?

Professional tree felling is the planned removal of a standing tree to ground level. It normally includes a site assessment, risk controls, preparation of the working area, controlled cutting and management of the resulting branches and timber. Stump removal is a separate operation unless it has been included in the quotation.

The main stages usually include:

  • Confirming the agreed tree and scope of work

  • Checking access and site-specific hazards

  • Confirming whether legal permission is required

  • Selecting whole-tree felling or sectional dismantling

  • Establishing an exclusion zone

  • Removing the crown or felling the stem under control

  • Processing branches and timber as agreed

  • Inspecting and tidying the work area

The exact sequence can change where a tree is unstable or where access is restricted. Weather may also affect whether the job can proceed safely.

The initial tree and site assessment

The initial assessment determines how the tree can be removed without creating avoidable risk. An arborist considers the tree’s structure as well as everything that could be affected by the work.

Tree condition and natural lean

The arborist examines the stem, unions, crown and visible root area for defects that could influence the work. Decay, cracks, cavities, dead branches and weak unions may make the tree less predictable when it is climbed or cut. The direction of lean and the distribution of crown weight also affect the intended direction of movement.

A tree that appears sound from the ground can still require additional precautions. If its structural condition is uncertain the method may be altered to reduce loading or avoid placing a climber in an unsafe part of the crown.

Surrounding targets and access

Targets are people or property that could be struck by falling material. Common examples include homes, sheds, fences, parked vehicles, greenhouses, roads and neighbouring gardens. The arborist also checks whether machinery and waste vehicles can reach the site.

Overhead electricity lines require particular care. Work close to power infrastructure may need coordination with the relevant network operator and should not proceed on assumptions about line type or voltage. Underground drains, cables and other services may affect where heavy timber or machinery can be placed.

Permissions and pre-work decisions

Before felling starts the responsible party should establish whether the tree is protected or whether the property is within a conservation area. A Tree Preservation Order can restrict tree work and conservation area controls may require prior notification. The position depends on the tree, location and proposed work so it should be checked with the relevant local planning authority.

Other constraints can also apply. A felling licence may be relevant in some circumstances depending on matters such as location and timber volume. Wildlife legislation must be considered throughout the year. Active bird nests, bats and other protected species can affect whether work should be delayed or adapted.

The quotation or work specification should make clear what is included. Useful points to confirm include:

  • Whether the tree will be felled whole or dismantled

  • Whether branches and timber will be removed

  • Whether logs will be cut to a requested size

  • Whether the stump will remain at a stated height

  • Whether stump grinding is a separate item

  • How access and parking will be managed

  • Who is responsible for checking permissions

How the work area is prepared

Site preparation creates a controlled working zone before cutting begins. The team normally moves vulnerable items where practical and establishes an exclusion zone around the tree. Access routes are kept clear for staff, equipment and emergency use.

The arborists may use barriers or other controls where members of the public could approach the site. On a roadside job this can involve additional traffic or pedestrian management. The required measures depend on the road, local conditions and any permissions imposed by the highway authority.

Tools and equipment are checked and positioned before work starts. Depending on the method these may include chainsaws, climbing equipment, lowering ropes, rigging devices, winches, wedges, wood chippers and timber handling machinery. Clear communication is important because ground staff may need to stop access or manage ropes while cutting takes place above them.

How arborists choose the felling method

The felling method is chosen according to available space, tree condition and nearby targets. The two main approaches are whole-tree felling and sectional dismantling.

Whole-tree felling

Whole-tree felling brings the main tree down in one planned direction. This method may be appropriate where there is enough clear space and the tree is structurally suitable. The arborist prepares the base and uses directional cuts to control the initial movement.

A face cut creates the intended direction of fall. A back cut is then made while retaining suitable hinge wood between the cuts. The hinge helps guide the stem during its descent. Wedges or a winch may be used where additional control is required. The precise cuts and equipment depend on stem form, lean, loading and tree condition.

Whole-tree felling is not automatically the quickest or safest choice. Open ground alone does not remove the need to consider wind, uneven weight, brittle timber and hidden defects.

Sectional dismantling

Sectional dismantling removes the tree in manageable pieces from the crown downwards. It is commonly used in gardens and built-up sites where there is not enough space to drop the whole tree.

An arborist may climb the tree using an appropriate rope system or work from a mobile elevating work platform where conditions permit. Smaller branches can sometimes be dropped into a clear area. Material above buildings, fences or delicate planting may be attached to rigging ropes and lowered under control by the ground team.

Once the crown has been removed the remaining stem is cut into sections. Large pieces can generate substantial force so their size and lowering method are planned around the strength of suitable anchor points, rigging equipment and landing area.

What happens while the tree is being cut?

During cutting the exclusion zone should remain clear of clients, neighbours and pets. The team uses agreed calls or signals so that cutting and rope operations are coordinated. Work can be paused if somebody enters the area or if site conditions change.

Branches are usually removed in an order that maintains control and avoids destabilising the remaining structure. In a dismantling operation the climber may reduce outer branches first before removing larger limbs. Loads are lowered or directed towards the chosen processing area.

Conditions are monitored throughout the job. Increasing wind, poor visibility, equipment issues or unexpected movement in the tree can require the method to be reassessed. A schedule should not take priority over safe working decisions.

Professional felling also involves controlling what happens after each cut. Ground staff manage ropes, move material and prevent branches from accumulating beneath the work position. This keeps escape routes and operational areas as clear as the site allows.

How branches, timber and the stump are handled

After the tree is down the branches and stem are processed according to the agreed specification. Smaller branches may be fed through a wood chipper. Larger limbs and stem sections can be cut into transportable pieces or left as logs if the client has requested this.

Woodchip can sometimes be left for use as mulch but its suitability and quantity should be discussed in advance. Timber can be heavy and difficult to move once stacked so the intended location should also be agreed before cutting starts.

Standard felling normally leaves a low stump and the root system in the ground. Cutting the stump close to soil level does not remove it. If the area needs to be replanted, paved or returned to lawn the client may wish to arrange stump grinding. The appropriate depth depends on the planned use of the area and site conditions.

Ground disturbance is possible during tree work. Falling timber, repeated foot traffic and machinery can affect lawns or soft ground. Protective measures may reduce damage but the practical options depend on access, weather and soil conditions.

Final checks after a professional tree felling job

The final stage is to check that the agreed tree work is complete and that the work area has been left in the specified condition. The team removes loose arisings included in the quotation and checks for tools, rigging equipment and material that could create a hazard.

The client should be shown any timber or woodchip retained on site and told about relevant next steps. These might include stump grinding, replacement tree planting or repairs to a fence that was removed to create access. If unexpected issues were discovered during the job they should be explained clearly.

Professional tree felling is therefore a managed sequence rather than a single cut. Assessment, legal checks, method selection, site control and coordinated handling of timber all contribute to the outcome. A site visit from a competent tree care contractor is the appropriate way to decide what a particular tree and property require.

Frequently Asked Questions

Do I need to be at home during a tree felling job?

Not always. The arborist normally needs confirmed access and a clear work area as well as agreement about timber, woodchip and the stump. If you will be absent you should discuss locked gates, pets, parking and access to utilities before the work date.

Can a tree be felled in wet or windy weather?

Light rain may not prevent all tree work but high winds, poor visibility, waterlogged ground or other adverse conditions can make felling unsafe. The decision depends on the tree, equipment and site so the arborist may postpone or alter the work.

Will professional tree felling damage my garden?

Arborists plan drop zones and may lower sections to protect lawns, structures and planting. Some ground disturbance can still occur because timber and machinery are heavy. The likely impact and suitable protective measures depend on access, soil and weather conditions.

How should I prepare before the arborists arrive?

Move vehicles, garden furniture and fragile pots away from the work area where possible. Keep pets and children indoors or outside the exclusion zone. Confirm access arrangements and tell the contractor about known underground services, septic systems or concealed structures.

Arrange a site assessment for safe and carefully planned tree felling.

Elite Tree Care & Gardening Services Ltd offer a range of Arborist, Tree Surgeon and other related services.

We welcome all enquiries and offer free quotes as standard.